Bushnell Binoculars 11 8321 User Manual

Model: 11-8321  
LIT. #: 98-0333/11-03  
 
LCD DISPLAY  
1.  
2.  
3.  
High Resolution Mode = 1600x1200 Pixels  
Low Resolution Mode = 1280x1024 Pixels  
Select the timer to take a delayed picture. This gives you  
approximately a 10-second delay.  
4.  
5.  
This mode allows you to take short movie clips, saved as .avifiles.  
Select different mode.  
6.  
Deletes all the pictures in the memory.  
7.  
Deletes the last picture taken.  
8.  
SD mark appears when SD is inserted.  
9.  
10.  
11.  
USB mark appears when USB cord is connected between the camera and the PC.  
Battery mark keeps track of the battery life left.  
a. Picture Number-- This area will show the number of pictures in the memory.  
b. SET-- select HQ (high quality)/LQ (low quality) mode, STO (Mass Storage)/ PCC (PC  
Cam) mode, 50Hz/60Hz frequency  
c. FUL--When the memory is full , the display will show FULand an alarm will sound.  
OPERATION GUIDE  
1. The camera is powered by one CR123A battery (not included) or USB power cable (included).  
2. Insert the battery into the battery compartment.  
3. Press and hold the MODE button until the camera turns on.  
4. Press SNAP to take a picture, or press the MODE button quickly to change mode settings as described  
above. The camera is set at infinity and will not be focused on an object closer than 49 feet.  
 
3
5. The mode setting operation is a cycle loop, so press the MODE button to switch to another mode.  
The loop order of the different modes is shown here:  
6. To change settings, toggle through the different modes by pressing the MODE button. When a  
mode is selected, the indicator symbol on the LCD will appear. You can then select that mode by  
pressing the SNAP button.  
7. When in Normalmode, press SNAP to take a picture.  
Press SNAP->  
8. Pressing the MODE button will cause the camera to enter Mode Change.  
9. To select Self-Timermode, press MODE and the self timer mark appears. Press SNAP and the  
capture will be done after 10 seconds. The camera exits self timer mode automatically after the  
capture is done and the self timer mark disappears on the LCD at the same time.  
Press MODE->  
press SNAP to capture.  
4
 
10.Low ResolutionMode will cause your pictures to be of a lower resolution, but allows you to store  
many more pictures in the cameras memory. The default setting is Hi resolution. To change the  
resolution, press the MODE button until the modeicon appears. Press the SNAP button and Lo”  
will appear. The camera is changed from high resolution to low resolution. Do the same steps for  
the desired resolution setting.  
CAPTURED PICTURES WITH BUILT-IN MEMORY:  
Pixels (resolution)  
Image quality  
Captured Picture Quantity  
1600X1200(Hi)  
High quality (HQ)  
Low quality (LQ)  
Up to 18 pictures  
Up to 25 pictures  
1280X1024(Lo)  
High quality (HQ)  
Low quality (LQ)  
Up to 24 pictures  
Up to 33 pictures  
11.When in Normalmode press the MODE button 3 times to enter the AVImode.  
The icon will appear. Press the SNAP button to start AVI capturing and counting.  
The resolution for AVI is 320X240 pixels. The AVI capturing can last for 40-70  
seconds as the captured objects and environment will vary.  
 
5
12.To delete all pictures in the cameras memory, select the Deletemode. Press the  
SNAP button to confirm. The picture number will then blink. You will hear a tone  
that becomes higher as the pictures are deleted. Once complete, the picture number  
will reset to possible captured numbers.  
13.If Delete Lasticon appears, the display will show the following: Press SNAP to  
delete the last picture in the cameras memory. The picture number will be  
automatically increased after deletion is done.  
14.When SD card is inserted into the card slot, the SD mark appears on the LCD. The  
captured pictures will be stored in the SD card once the card is inserted. The captured  
picture numbers will be different with different memory capacity of the SD card.  
15. Press the MODE button until SET mode appears on the LCD. Press SNAP to enter  
Setting mode. To change the setting of image quality (default setting is High),  
Storage/PC Cam (default setting is Storage), 50 Hz/60 Hz frequency (default setting  
is 60 Hz), follow the steps below:  
a. Select the image quality at HQ (High quality) or LQ (Low quality) by pressing the SNAP button.  
Then press the MODE button to confirm and enter the next setting.  
6
 
b. Select the STO (Mass Storage) or PCC (PC CAM) mode by pressing the SNAP button. Then  
press the MODE button to confirm and enter the next setting.  
c. Select 50 Hz or 60 Hz settings for the camera output by pressing the SNAP button. Then press  
the MODE button to confirm and enter the next setting. The cameras default mode is the 60”  
mode, which matches the power frequency for the United States. To change to the 50mode,  
press the SNAP button until the 60changes to 50. Confirm the selection by pressing the  
SNAP button. To avoid any flickering on the picture, the correct power frequency (either 50 or 60)  
for your country must be selected.  
d. Escape the Setting mode by pressing the SNAP button.  
16.The battery mark keeps track of the battery life. If the Batteryindicator is blinking, it is necessary  
to replace the batteries soon.  
 
7
DOWNLOADING THE PICTURES TO YOUR COMPUTER:  
1. The camera will be recognized as a USB mass storage device, which means no special drivers are  
required for all operating systems later than Windows 98 (Me, 2000, XP). Mac OS 9 and OSX are  
also compatible. If you have a PC running Windows 98, you must install the driver found on the  
included CD-ROM BEFORE CONNECTING THE CAMERA TO YOUR PC.  
2. If you have a computer OS as listed above that is USB mass storage compliant, a new disc icon will  
appear in Windows Explorer (under My Computer) as a new Removable Discafter plugging in  
the USB cable from the Imageview. Mac users will see the new disc device appear on their desktop.  
Clicking on the new disc icon will show the contents, a folder named DCIM. The image folder  
inside this contains your photos, stored as JPEGs (.jpg file format). They may then be opened,  
edited, renamed and saved using any photo or graphics software that accepts .jpg files. If you do not  
have software that will open .jpg files, you should install MGI Photosuite (Windows only) from the  
included CD-ROM. See Software Installationfor instructions.  
3. After you have copied or opened and saved the photo files to your computers hard drive, you may  
disconnect the Imageview camera (NEVER disconnect the camera while files are still being  
transferred to your computer). Before disconnecting, you should ejector stop the removable disc  
representing the camera to avoid an error message.  
8
 
CONNECTING TO THE COMPUTER - System Requirements:  
Pentium 166MMX minimum (Recommended Pentium 266)  
Windows 98 / ME / Windows 2000 / XP  
Minimum 32MB of RAM  
USB port  
Minimum 200MB of Hard Drive space with additional 65 MB space for IE and DirectX  
CD-ROM driver  
Super VGA Monitor and video card  
SOFTWARE INSTALLATION  
Load software prior to connecting your camera to your computer if the OS is Windows 98. If the OS  
is Windows2000/ME/XP, there is no need to install driver. Simply plug in the camera and use.  
To load software insert the CD into your CD-ROM drive and it will self-start. The CD contains the  
Roxio Photo Suite software as well as the drivers that will allow your computer to recognize your camera.  
Follow the On Screeninstructions. If your computer does not have an auto play function and will not  
automatically run CDs, open the CD in the My Computerwindow and click on the autorun.exe. After  
the drivers are successfully installed, click on Roxio Photo Suite to install the photo imaging software.  
WARNING:  
Make sure you download any picture from your camera  
before you remove the batteries from the camera.  
Follow the instructions on the software to successfully download and save the pictures on your  
computer. An installation screen will automatically guide you through the installation process.  
 
9
BINOCULAR INSTRUCTIONS  
Your Bushnell binocular is a precision instrument designed to provide many years of pleasurable  
viewing. This portion of the booklet will help you achieve optimum performance by explaining how  
you can adjust the binocular to your eyes, and how to care for this instrument. Read the instructions  
carefully before using your binocular.  
EYE ADJUSTMENTS (Figure 1)  
How to Adjust For Distance Between Your Eyes  
Fig. 1  
The distance between the eyes, called "interpupillary distance," varies from  
person to person. To achieve perfect alignment of lens to eye, follow these  
simple steps.  
INTERPUPILLARY DISTANCE  
1. Hold your binocular in the normal viewing position.  
2. Grasp each barrel firmly. Move the barrels closer together or further apart  
until you see a single circular field. Always re-set your binocular to this position before using.  
How to Adjust For Individual Eye Strength  
As individual eyesight varies from one person to another, most Bushnell binoculars have a diopter setting  
feature which allows you to fine-tune the binocular to your vision. Follow the focusing instructions below  
for your type of binocular.  
10  
 
FOCUSING  
1. Adjust interpupillary distance. (Figure 1)  
2. Set the "diopter setting" (Figure 2) to zero and view a distant object.  
3. Keep both eyes open at all times.  
Fig. 2  
4. Using a lens cover or your hand, cover the objective (front) lens of the  
same side of the binocular that has the "diopter setting." This is usually  
the right side. (The left side on zoom models.)  
DIOPTER SETTING  
5. Using the center focus wheel, focus on a distant object with fine detail (e.g., brick wall, tree  
branches, etc.) until it appears as sharp as possible.  
6. Uncover the objective lens on the diopter side, cover the other objective lens, then view the same object.  
7. Using the "diopter setting" adjustment ring, focus the same object being viewed. Caution should  
be used as over turning or forcing the diopter eyepiece can cause damage or cause the eyepiece to  
break away from the chassis.  
8. Your binocular should be adjusted for your eyes. Focus at any far or near distances can now be  
attained simply by turning the center focus wheel. Make a note of the diopter setting for your eyes  
for future reference.  
Fig. 3  
EYECUPS (Figure 3)  
Your Bushnell binocular is fitted with rubber roll-down eyecups designed for  
your comfort and to exclude extraneous light. If you wear sun/eyeglasses, roll  
down the eyecups. This will bring your eyes closer to the binocular lens thus  
providing improved field of view.  
ROLL-DOWN EYECUPS  
11  
 
INSTRUCTIONS FOR CARE OF BINOCULARS  
Your Bushnell binocular will provide years of trouble-free service if it receives the normal care you would  
give any fine optical instrument. Non-waterproof models should not be exposed to excessive moisture.  
1. If your binocular has roll-down, flexible eyecups, store it with the eyecups up. This avoids excessive  
stress and wear on the eyecups in the down position.  
2. Avoid banging and dropping.  
3. Store in a cool, dry place.  
4. CAUTION: Looking directly at the sun with your binocular may be very harmful to your eyes.  
5. Never expose your ImageView binocular to any type of excessive of liquid or fluid, as the binocular  
is not water/fogproof.  
6. Take the batteries out of your ImageView if you are not going to use for a long period of time. (Make  
sure you download any pictures from your camera before you remove the batteries out of the camera.)  
CLEANING  
1. Blow away any dust or debris on the lens (or use a soft lens brush).  
2. To remove dirt or finger prints, clean with a soft cotton cloth rubbing in a circular motion. Use of  
a coarse cloth or unnecessary rubbing may scratch the lens surface and eventually cause permanent  
damage. A "microfiber" cleaning cloth (available at most photo dealers) is ideal for the routine  
cleaning of your optics.  
3. For a more thorough cleaning, photographic lens tissue and photographic-type lens cleaning fluid  
or isopropyl alcohol may be used. Always apply the fluid to the cleaning cloth never directly on  
the lens.  
12  
 
WARRANTY / REPAIR  
TWO-YEAR LIMITED WARRANTY  
Your Bushnell® product is warranted to be free of defects in materials and workmanship for two years after the date of purchase. In the  
event of a defect under this warranty, we will, at our option, repair or replace the product, provided that you return the product postage  
prepaid. This warranty does not cover damages caused by misuse, improper handling, installation, or maintenance provided by someone  
other than a Bushnell Authorized Service Department.  
Any return made under this warranty must be accompanied by the items listed below:  
1) A check/money order in the amount of $10.00 to cover the cost of postage and handling  
2) Name and address for product return  
3) An explanation of the defect  
4) Proof of Date Purchased  
5) Product should be well packed in a sturdy outside shipping carton, to prevent  
damage in transit, with return postage prepaid to the address listed below:  
IN U.S.A. SEND TO:  
Bushnell Performance Optics  
Attn.: Repairs  
8500 Marshall Drive  
Lenexa, Kansas 66214  
IN CANADA SEND TO:  
Bushnell Performance Optics  
Attn.: Repairs  
25A East Pearce Street, Unit 1  
Richmond Hill, Ontario L4B 2M9  
For products purchased outside the United States or Canada please contact your local dealer for applicable warranty information. In Europe  
you may also contact Bushnell at:  
BUSHNELL Performance Optics Gmbh  
European Service Centre  
MORSESTRASSE 4  
D- 50769 KÖLN  
GERMANY  
Tél: +49 (0) 221 709 939 3  
Fax: +49 (0) 221 709 939 8  
This warranty gives you specific legal rights.  
You may have other rights which vary from country to country.  
©2003 Bushnell Performance Optics  
13  
 
NOTES  
14  
 
NOTES  
15  
 
©2003 Bushnell Performance Optics  
 

Belkin Septic System ST4125D User Manual
Black Box Network Router LRB500A User Manual
Blanco Indoor Furnishings 157 014 User Manual
Bloomfield Coffeemaker 0420 User Manual
Bogen Speaker System FH 1 User Manual
Bosch Power Tools Drill 33614 User Manual
Braun Electric Shaver BS7511 User Manual
Calphalon Slow Cooker 1779208 User Manual
Campbell Hausfeld Nail Gun IN729000AV User Manual
Carrier Refrigerator 19EA User Manual