MA0702-EA
Operation Guide DQD-106
• A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the
ILLUSTRATION
clock.
• Depending on its model number, the appearance of your clock may differ somewhat from that shown in the
illustration.
4 5
Alarm Off
Antenna Icon
Snooze Alarm On
Current time
(Hour, minutes, seconds)
Snooze on indicator
DST indicator
PM indicator
2
Alarm on indicator
Day of the week
Wave OK indicator
Date (month – date)
Current Temperature
3 6
7
GENERAL GUIDE
1SNOOZE/LIGHT button
• Press this button to illuminate the display for about four seconds.
• Pressing this button while the alarm is sounding stops the alarm.
2Alarm Mode selector
SNZ: Snooze alarm on
ALM ON: Alarm on
1
ALM OFF: Alarm off
3Alarm Time Set buttons
Use these buttons to change the alarm time or current time setting.
4SET button
Use this button when setting the current time.
5WAVE button
Press this button to receive the time calibration signal and adjust timekeeping.
1
6°C/°F button
Press this button to toggle the temperature units between Celsius and Fahrenheit.
2
7RESET button
Press this button to reset the clock after replacing its batteries.
8Batteries
8
1
Operation Guide DQD-106
USING THE ALARM
THERMOMETER FUNCTIONS
The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm
Mode selector (2) to select the snooze alarm feature.
A built-in sensor measures temperature and shows the measured value on the display. The readout from the
temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F).
Setting the Alarm Time
Temperature Measurements
Use the Alarm Time Set buttons (3) to set the alarm time.
Pressing the Alarm Time Set buttons (3) causes the alarm time to appear in place of the time on the display.
• The temperature display shows “LO” for temperatures below –50°C (–58°F) and “HI” for temperatures above
70°C (158°F).
• Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such
readings are actually outside the guaranteed temperature range of this clock.
Press to change the
alarm time setting (+).
Press to change the
alarm time setting (
Switching between Celsius and Fahrenheit
• Push the °C/°F button (6) to select either Celsius (°C) or Fahrenheit (°F).
—
).
Celsius (°C)
Fahrenheit (°F)
°C/°F button (6)
°C/°F button (6)
• Holding down + or – changes the digits at high speed.
Turning the Alarm On and Off
Use the Alarm Mode selector (2) on the side of the clock to turn the alarm on and off, and to select the snooze
feature.
Alarm Mode selector
SNZ
Description
°C
°F
The alarm sounds at the preset time for one minute, and seven
more times every five minutes thereafter. Even if you stop the
alarm sound by pressing the SNOOZE/LIGHT button (1), the
alarm operation is performed again five minutes later.
flashes on the display to indicate that the
snooze feature is activated.
BATTERY REPLACEMENT
Replace batteries whenever the display of the clock becomes dim and difficult to read.
1. Open the battery compartment cover as shown in the illustration.
2. Remove all of the old batteries.
( )
• The indicator
3. Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct
directions. If you load batteries incorrectly, they can burst and damage the clock.
4. Replace the battery compartment cover.
ALM ON
The alarm sounds at the preset time for one minute.
5. Press the RESET button (7). Be sure to press the RESET button (7) after replacing batteries.
( )
ALM OFF
Battery precautions
• Keep batteries out of the reach of small children. If a battery is swallowed accidentally, contact your physician
The alarm does not sound.
immediately.
• Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.
• Never mix old and new batteries, or batteries of different brands.
• Never charge the batteries that come with the clock.
• The light also turns on for the first five seconds that the alarm sounds.
• The alarm sound changes over four levels as it sounds.
Stopping the Alarm
• Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto
your skin.
• When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned
• Replace the batteries at least once a year, even if the current batteries are working properly.
• The batteries that come with the clock lose some of their power during transport and storage.
on, the alarm will sound again in about five minutes.
• To turn off the snooze feature, slide the Alarm Mode selector (2) to ALM OFF.
USING THE LIGHT
Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the
dark.
Important!
• Overuse of the light can shorten battery life.
3
|